Galvanized Wire Processing Electric Welding Mesh: Specifications, Quality Standards, and Precautions


Release time:

2024-11-28

The following is a detailed introduction to the specifications, quality standards, and specific precautions for galvanized iron wire processing electric welding mesh:

The following is a detailed introduction to the specifications, quality standards, and specific precautions for galvanized iron wire processing electric welding mesh:

Specifications

  1. Wire diameter:
    • The diameter range of commonly used galvanized iron wires is relatively wide, usually ranging from 0.5mm to 3mm. For example, in some ordinary protective electric welding meshes, wire diameters such as 0.8mm, 1mm, and 1.2mm are often used. Thinner wire diameters are suitable for occasions where the strength requirement is not particularly high but the fineness is required, such as small animal breeding fences; while thicker wire diameters are mostly used in places that need to withstand greater external forces and have high protection levels, like prison protection nets.
    • There are usually certain standards for the allowable deviation of the wire diameter. Generally, it is about ±0.05mm. However, the specific deviation requirements will vary according to different industry standards and application scenarios.
  2. Mesh size:
    • The common mesh shapes are square and rectangular. The side length specifications of square meshes are diverse. For example, 1/2 inch (about 12.7mm), 3/4 inch (about 19.05mm), 1 inch (about 25.4mm), and there are also larger size specifications such as 50mm×50mm, 60mm×60mm, etc. They are often used in building exterior wall insulation protection, land enclosure fences, and other aspects. Rectangular meshes can be customized with different lengths and widths as required, such as 20mm×40mm. In some places with special requirements for ventilation and light transmission, this mesh shape will be adopted.
    • There are also corresponding requirements for the deviation of the mesh size. The side length deviation of square meshes is generally controlled within the range of ±1mm to ensure the dimensional accuracy and appearance uniformity of the electric welding mesh as a whole.
  3. Mesh sheet size:
    • In terms of width, common specifications include 0.5m, 1m, 1.2m, 1.5m, 2m, etc. The length can be customized according to actual usage needs. For example, common lengths include 10m, 20m, 30m, etc. For large application scenarios such as highway guardrails and breeding site fences, longer mesh sheets are often used for splicing and installation, while smaller and narrower mesh sheets may be sufficient for small household garden fences.
    • The allowable deviation of the mesh sheet size is usually about ±5cm in the width direction and about ±10cm in the length direction to ensure smooth splicing and the achievement of expected coverage and protection effects during installation.

Quality Standards

  1. Quality of the galvanized layer:
    • Appearance: The galvanized layer should be uniform and continuous, and there should be no defects such as missing plating, black spots, peeling, or falling off on the surface. Under normal circumstances, it presents a bright metallic luster. High-quality galvanized electric welding meshes give a flat and smooth feeling in appearance, which can ensure good corrosion resistance and aesthetics in outdoor and other environments.
    • Thickness: According to relevant standards, the average thickness of the hot-dip galvanized layer should generally not be lower than the specified value. For example, in some electric welding meshes used in ordinary environments, the average thickness of the galvanized layer may be required to be more than 45μm. For electric welding meshes used in harsh corrosive environments (such as near the seaside or chemical plants), the average thickness of the galvanized layer often needs to be more than 80μm to ensure sufficient anti-corrosion years. The specific thickness requirements will vary according to different usage occasions and industry norms.
    • Adhesion: The galvanized layer should be firmly bonded to the iron wire substrate. When tested by methods such as the bending test, the galvanized layer should not show phenomena such as peeling or flaking. This can ensure that the galvanized layer continues to play a role in anti-corrosion during the processing, installation, and subsequent use of the electric welding mesh.
  2. Welding quality:
    • Firmness of welding points: The welding points should be full and firm. The connection points formed by welding between adjacent iron wires should be able to withstand certain tensile and shear forces. For example, when performing a tensile test, a single welding point should be able to withstand a tensile force of not less than the specified value. For commonly used specifications of electric welding meshes, the tensile force of a single welding point is generally required to be more than 100N to ensure that the welding points will not easily crack or come off under normal use, external impact, or stretching, and to ensure the stability of the overall structure of the electric welding mesh.
    • Uniformity of welding: The distribution of welding points throughout the electric welding mesh should be uniform, and the spacing should meet the design requirements. There should be no false welding or missing welding, so that all parts of the electric welding mesh can bear the force evenly, the overall strength is consistent, and the appearance is more regular.
  3. Mechanical properties:
    • Tensile strength: The galvanized iron wire itself should have a tensile strength that meets the requirements. Generally, it varies according to the material of the iron wire (such as low-carbon steel wire, etc.) and specific specifications. For example, the tensile strength of commonly used low-carbon galvanized iron wires may be between 300MPa and 500MPa. It should be able to withstand a certain tensile force without breaking to meet the mechanical requirements in application scenarios such as fences and protection.
    • Elongation: The iron wire should have a certain elongation to ensure that it has a moderate deformation ability without brittle fracture under the condition of being stretched by external forces. The elongation is usually required to be about 10% - 25%. Different electric welding meshes for different purposes can determine the specific range of elongation index according to actual needs.

Specific Precautions

  1. Raw material procurement:
    • Choose regular and reputable suppliers to purchase galvanized iron wire, and check the quality certificate documents provided by them, such as material test reports and galvanized layer inspection reports, to ensure that the wire diameter, material composition, and galvanized quality of the raw materials meet the production requirements and control the product quality from the source.
    • Conduct random inspections on the purchased raw materials, check basic indicators such as wire diameter and the appearance of the galvanized layer. If unqualified products are found, communicate with the supplier in time for return or replacement to avoid unqualified raw materials entering the production process.
  2. Processing and production:
    • Debugging of welding equipment: Before starting production, accurately debug the welding equipment, set appropriate welding current, voltage, and welding time parameters according to the wire diameter, mesh size, etc., and regularly check and calibrate these parameters during the production process to ensure the stability of the welding point quality.
    • Production operation specifications: Operators should strictly follow the established production process flow for operation. For example, in the steps of wire feeding, mesh pulling, and welding, ensure the coherence and accuracy of the actions to avoid quality problems such as wire diameter deformation, mesh size deviation, and unqualified welding points caused by improper human operation. At the same time, operators are required to take good personal safety protection measures and wear corresponding protective equipment.
    • Quality patrol inspection: Arrange special personnel to conduct quality patrol inspections on the production line, focusing on checking welding quality, mesh size, wire diameter and other indicators. If problems are found, stop the machine in time for adjustment. For the links with more quality problems, conduct in-depth analysis of the causes and take corresponding improvement measures to prevent the generation of mass defective products.
  3. Finished product inspection and packaging:
    • Full inspection or sampling inspection of finished products: Conduct a comprehensive inspection or sampling inspection of the produced electric welding mesh finished products according to a certain proportion, and check various indicators such as the quality of the galvanized layer, welding quality, and dimensional specifications in detail according to the quality standards. Mark and isolate the unqualified finished products. Depending on the actual situation, they can be reworked and repaired or scrapped.
    • Packaging protection: When packaging qualified finished products, choose appropriate packaging materials, such as moisture-proof paper and plastic film. For electric welding meshes that need to be transported over long distances or stored for a long time, take good anti-moisture and anti-rust protection measures, and mark relevant information such as product specifications, quantity, and production date on the packaging for easy identification and management.

In general, in the entire process of galvanized iron wire processing electric welding mesh, strict control of each link and compliance with corresponding specification requirements and quality standards can produce electric welding mesh products with reliable quality and meeting usage requirements.

Additional Resources

  • Galvanized wire mesh 17 gauge electric galvanized

  • Galvanized Weld Wire Mesh PVC Coated Wire Mesh

  • Wire Mesh︱Galvanized Wire︱Wire Mesh Fences

  • Galvanized Wire Manufacturer, Welding mesh, Metal mesh